PORT vs DIRECT vs DUAL INJECTION - a DETAILED comparison -EVERYTHING you need to know in 1 video

PORT vs DIRECT vs DUAL INJECTION - a DETAILED comparison -EVERYTHING you need to know in 1 video

Show Video

What is up Engineheads? Today, we'll be doing a detailed comparison   of three different kinds of  gasoline fuel injection systems. Port Fuel Injection Direct Injection And Dual Injection. We'll see how each system works. And we'll see how they differ from each other. And of course, we're going to examine  the benefits and drawbacks of each setup.

So, let's get started. So, both port and direct injection  essentially do the same thing. As the name implies, they inject fuel.

So, that the fuel can mix with the air  and create a combustible air-fuel mixture. Which when combusted,  creates combustion pressures,  which drive the piston downward, which spins the crankshaft,  which then ultimately turns the wheels of the vehicle. Now they may do the same thing,  but port and direct injection differ in  the location of where they inject the fuel. As the name again implies,  port fuel injection injects the fuel  into the intake port of the engine.

Before the intake valve. Whereas direct fuel injection injects the  fuel directly into the combustion chamber. After the intake valve.

This means that in the case of port injection,  you're usually going to find the injectors  somewhere on the intake manifold of the engine. While in the case of direct injection, the injectors are going to be either   on the valve cover, or if they're not there, you're going   to find them underneath the intake manifold. Protruding directly into the cylinder head. Although the location of fuel injection  may seem as something trivial. In reality, it plays a fundamental  role in the design of the engine. And noticeably influences performance,  efficiency, emissions, and maintenance concerns.

Now, both systems: Port and direct injection,  consist of essentially the same parts. A fuel tank or fuel reservoir, a fuel pump, some fuel lines, and fuel injectors. Now, the engine control unit, or the ECU, measures the amount of air coming into the engine.

Using various sensors. And then tells the injectors how much fuel to inject, so that the   amount of fuel injected corresponds to  the amount of air entering the engine. All with the goal of creating combustion  that is as close to ideal as possible. But direct injection has a more  challenging task than port injection. Because fuel is injected directly into the combustion chamber,  the direct injectors must spray the fuel with sufficient force   to overcome the pressures generated by the engine's compression.

And if you have ever compression tested an  engine, you know that the upward movement   of the piston inside the engine can easily  generate pressures in excess of 100 psi. Now, port injectors don't have to  combat this compression pressure,  because they're injecting  fuel before the intake valve. Which means that they're  injecting either into atmosphere  (If they start injection before the intake valve opens) Or they're injecting into a vacuum  (If they start injecting after the intake valve opens) This means that port injection needs somewhere  between 40-65 psi to operate properly. This is obviously than the compression  pressures generated by the engine itself,  which means that if you try to use a port injector, to inject   fuel directly into the combustion chamber, the fuel would actually never leave the injector.

This is why to ensure that it can easily  overcome the pressures generated by the engine's   compression, direct fuel injection usually  operates at fuel pressures upwards of 2,000 psi  That's 140 bars Which is 140 times the pressure of earth's atmosphere  And it's also 20 times the pressure  of the engine's compression. But of course to generate such high pressures,  direct injection needs additional parts. First of all, it can't work with a simple  one fuel pump setup like port injection. Instead, it needs two fuel pumps.

The first one is an in-tank  low-pressure fuel pump,  which sends fuel down the lines from the tank. To a camshaft driven, high-pressure fuel pump,  which ramps up the pressure to the required   amount, and then sends it into a fuel rail  from where it gets distributed the injectors. The injectors themselves are also  radically different to port injectors. They're more advanced, because they need to  be capable of rapidly opening and closing   against very high fuel pressures. And also because their tips are located  directly inside the combustion chamber.

They must be capable of operating  properly, while being exposed   to the extremely harsh conditions  created by the engine's combustion. Port injectors of course don't  have any of these concerns,  which is why in general they're much  less expensive and far less complex   than direct injectors. In general, a direct injection  system because of the increased   complexity and increased number of parts, increases production costs and vehicle prices. So, as we have seen the location  of the injection determines the   pressure at which the system needs to operate. And it also drives up the  number and complexity of parts. But if you have paid attention, you might have  also noticed that the location of the injection   also determines the timing of the injection.

As we have said, port injectors  inject either into vacuum or   into atmospheric pressure, if injection  starts before the intake valve opens. And when does the intake valve open? Of course during the intake stroke of the engine. And this tells us that port injection  occurs during the intake stroke. In fact, it can occur during any other  time during any other stroke of the engine.

But the fuel actually gets into the  chamber during the intake stroke. When it comes to direct injection,  you may recall that it has to face the  compression pressures of the engine. And when does the engine  generate compression pressure? Of course during the compression stroke. And this tells us that direct injection occurs  during the compression stroke of the engine. In fact, in most modern more recent systems,   direct injection occurs during the  later stages of the compression stroke.

Right before combustion occurs. And although in some older system,  a direct injection would occur   at early stages of the compression stroke,  or even earlier during the intake stroke,  depending on the engine speed and engine load In general, direct injection starts much later. And is of much shorter duration  than port fuel injection. So, how does the timing of the  injection affect the engine?  Well, for one, it enables a higher compression  ratio in the case of direct injection. Now, don't be confused. Compression pressure, is the pressure generated by   the upward movement of the  piston inside the engine.

But the compression ratio, is  the ratio between the largest   and the smallest cylinder volume of the engine. The higher the compression ratio,  the more we compress the air-fuel  mixture inside the cylinder. The more we compress it,  the closer we bring the piston  to the heart of the combustion. And the closer the piston to the combustion, the more of the combustion's energy   can be transferred onto the  piston, and turned into motion. In other words, a higher compression  ratio can lead both to better performance   and higher efficiency. So, how exactly does different injection timing enable a higher compression ratio? Well, to understand that, we need observe port and direct injection side by side.

And as you can see, in the case of port injection,  the fuel enters the cylinder much earlier, and spends more time in the cylinder,  than in the case of direct injection, where the fuel enters only at the  late stage of the compression stroke. Now, you have to remember that  the insides of an engine are hot. Temperatures inside the cylinder are always high,  because combustion occurred there  just a few milliseconds ago. The intake valves also carry a lot of heat,   because they're constantly exposed  to the heat of the combustion. And the air-fuel mixture  coming inside the cylinder   of a port injected engine, has to  pass right along the intake valve.

And it's picking up heat from  the valve, as it does so. And all this heat inside the engine means,  that the more time the air-fuel mixture  spends inside the engine, the hotter it gets. And the hotter it gets,  the greater the chances of  its spontaneous combustion. Or knock.

Now, knock is spontaneous abnormal  combustion of the air-fuel mixture,  that occurs after the spark plug is fired. And it occurs outside the evenly propagating  flame front initiated by the spark plug. Now, for the air-fuel mixture to  spontaneously self ignite, it needs heat. And it needs a lot of heat. And this heat can come from two main sources. The first source is the compression  of the air-fuel mixture itself.

The more we compress a gas, the closer we  bring its molecules together, causing them   to bump against each other more, increasing  their friction and thus the heat of the gas. Now, the air-fuel mixture is of course also a gas. Which means that the more we compress it, the  higher the compression ratio, the greater the   heat of the air-fuel mixture, and the greater  the chance of its spontaneous self-ignition. Now, the second source of the heat  comes from the combustion itself.

When the spark plug fires,  it initiates a flame front which spreads  evenly outward from the spark plug. Of course, this flame front exerts heat and  pressure on the uncombusted air-fuel mixture   outside of this flame front And if the uncombusted air-fuel   mixture is already hot enough from the  compression, then the added heat and   pressure from the combustion can cause it  to ignite spontaneously leading to knock. And if knock persists long enough and if it's  strong enough it will destroy the engine. Now, as we said the air-fuel  mixture spends more time   inside a port injection engine than  it does in a direct injection engine. Which means that it picks up more heat,  and it's already at a higher  temperature when combustion starts. Now, when we add the heat of compression and the   heat of combustion onto the already  higher base heat of the air-fuel mix   inside a port injected engine, it means that  we can enter 'Knock territory' more easily.

And result is, that we have to be somewhat conservative with a compression ratio   inside a port injected engine to prevent knock. Now, in the case of direct injection, as we said,   the fuel enters the system later, at a late stage of compression,  which means that the air-fuel mixture spends  less time inside the cylinder, picking up heat. Which results in a lower base heat once combustion starts.

And because of this we have more  room to increase the compression   ratio of the engine in a direct injection setup. And as we said, a higher compression ratio can lead to better power and more efficiency. And this is one of the key reasons why so much   research and development has been invested into direct injection.

The other key benefit of direct  injection is that it can reduce   fuel consumption and harmful emissions. It can do this, because it sprays fuel directly into the combustion chamber. Which means that the fuel sprayed by the injectors,   is the same amount of fuel that actually ends up  in the combustion chamber, and can be combusted. But this is not the case with port injection.

Because fuel is injected  outside the combustion chamber,  the amount of fuel released by the injectors  is not necessarily the same amount of fuel   that ends up in the combustion chamber. Some of the fuel may end up  as droplets that accumulate   on the walls of the intake manifold  or the intake of the cylinder head. Also, the intake valve might close before all the air-fuel mix enters the cylinder. And the result is, that the difference  between fuel injected and fuel combusted,   is greater in port injected engines. Resulting in less accuracy and less  control over the injection process,   which can negatively impact  emissions and fuel economy.

But there are two sides to every coin. And what may seem as drawbacks of port injection, can also be its benefits in different scenarios. As we said, the air-fuel mixture spends more time  inside the cylinder of a port injected engine. And although this allows it to pick up more heat,  and ultimately limits the compression ratio,  it also gives the fuel more time  to vaporize and mix with the air.

To achieve good combustion you want to  burn all the fuel inside the cylinder. And to do that you want the air-fuel  mixture to be as homogeneous as possible. In other words, you want the air and fuel well mixed together And one way of doing that, is tumbling the air-fuel mixture as much as possible. Now, there's plenty of time for tumbling the  air-fuel mix inside a port injected engine. It first occurs when the air and fuel enter  the cylinder together and swirl around.

And then it occurs some more during  the entire compression stroke,   when the piston rapidly pushes  the air-fuel mixture upward. But unfortunately, direct injection doesn't have   nearly the same amount of time  available to vaporize the fuel. As we said, most recent setups start injecting  only in the second half of the compression stroke. Now, direct injection makes up for this,   by having extremely high fuel pressures  which dramatically improve fuel atomization. And also it uses tricks like cavities,  special cavities, in pistons.

Against which fuel is sprayed, and against  which the air-fuel mixture tumbles and swirls. But despite this, direct injection can   suffer from poor air-fuel mixture  homogenization at low engine speeds. At low RPMs, the piston speeds are also lower. Which means that the piston pushes  against the air-fuel mixture more slowly, causing it to tumble less. Which means that at low RPMs, direct injection   engines can experience little pockets of  unburned fuel within the air-fuel mixture.

This of course results in  less than perfect combustion And increased emissions And reduced efficiency at low RPMs. This means that depending on the engine  and fuel system design, in some cases,   a port injected engine may  have less emissions and better   efficiency than a direct  injected engine at low RPMs. Another problem the direct injection faces,  is supplying enough fuel at high RPMs. Let's imagine an engine running at 6,500 RPM. At 6.5K rotations per minute, one single  engine-rotation or revolution, lasts only   9 milliseconds.

Which means that one single  engine-stroke is 4.5ms. And as we said, most recent  direct injection setups,   only start injecting in the second  half of the compression stroke. Which means that there's only 2.25ms of time available

to inject all the fuel that's needed. To put this into perspective, the average human blink is 100-150ms. Now, even if we were to somehow start injecting  at the very beginning of the intake stroke (which never happens) This gives us only 18ms to inject the  fuel before combustion actually starts. Now, port injection doesn't have to worry about the start of the combustion event.

Because the injector sits behind the intake valve. Which is closed during the combustion stroke, and at all other strokes except the intake stroke,  which means that it's keeping the  injectors away from combustion. In other words, in the case of port injection,  we can start injecting during  the compression stroke. And keep injection throughout the  combustion and the exhaust stroke,  all the way until the next intake stroke,  when the intake valves open again. The fuel will simply accumulate  behind the intake valves, and enter all at once, when the valves open again. This means that if you install injectors with sufficient capacity   inside a port injected engine, you will never run out of fuel.

In other words, you can rev as  high as your internals can survive. The port injection setup will never  be an obstruction to your RPM limit. But that's not the case with direct injection.

Because as RPMs increase, the time frame for injection becomes so small,  that no amount of injector capacity  or fuel pressure can make up for it. And this is why on average direct injection  only engines are limited to about 6,500 RPM. There are exceptions with more RPM,   with higher RPM limits that are achieved  at the expense of emissions or efficiency,  but the common RPM limit is  usually around 6,500 RPM or less. Now, the location of injection carries one  final benefit in favor of port injection.

Now, gasoline is a great solvent. Wanna clean an old greasy gunky part? Just get some gasoline & a brush, and watch magic happen. And as we said, the backs of the intake  valves in a port injected engine are   constantly exposed to the stream of  gasoline coming from the injectors.

Which means that they can never get dirty. They're constantly being cleaned. Of course, this is not the case  in direct injection engines,  because the injector is  inside the combustion chamber. And thus it never sprays fuel  on the back of the intake valves Which means that all sorts of carbon deposits,  gunk and other junk from the vehicle's PCV system   can accumulate on the back of the intake  valves in direct injection only engines. Now, over time these deposits can pile  up so much on the backs of the valves,  that they lead to a distorted and  reduced cross-section of the intake port.

Which means that less air  can come into the engine. Which of course reduces performance and/or leads to a rough running engine. Now, there are ways to try and prevent these  deposits. Using oil catch cans or fuel additives. But results are mixed. And the need to eventually mechanically clean  the backs of the valves is simply inevitable. And it usually happens when the engine has  around 100-150 thousand kilometres on it.

Now, this is of course a time  consuming and expensive job. Which sometimes even requires the  complete removal of the cylinder head,   to access the valves and everything. Of course, this leads to increased  maintenance cost for direct injection engines  Something that many see as the  main drawback of these engines. Another potential issue with  direct injection only engines. Especially earlier models of these engines.

Is that the constant introduction of  fresh, sometimes poorly vapourized fuel,   would actually dilute or wash away the  protective layer of oil on the cylinder walls. This of course would lead to increased wear  and tear, and reduced engine longevity. However, newer models have overcome  this issue by changing the direction   of the injection away from the cylinder walls.

Which means that most newer direct injection only  engines, don't really suffer from this issue. Another problem that the deposits in the  backs of the valves can contribute to is LSPI. Or Low Speed Pre Ignition.

Now, as we've said: Knock is abnormal combustion that  occurs AFTER the spark plug has fired. Pre-ignition is abnormal combustion that  occurs BEFORE the spark plug has fired. And pre-ignition is in most cases  worse and damaging the knock Because the piston is moving into the abnormal  combustion, instead of running away from it. As in the case of knock.

Now, Low Speed Pre Ignition occurs during  low speed and the high engine load scenarios. As we've said, during low engine  RPM/low engine speeds, the pistons   and direct injection only engines have trouble  tumbling and mixing of the air-fuel mixture. Because the piston moves slowly. Leading to pockets of unburned fuel  floating around in the air-fuel mixture.

At the same time, a higher load scenario means,   that the ECU will instruct the injectors to inject more fuel. So in other words, you need to floor it from  low RPM in a direct injection only engine,   to create the preconditions needed for LSPI. Now the other thing that needs to happen,   is that a particle from the back of the valves,  needs to fall off and enter the chamber. Or maybe an oil droplet makes it pass  the piston rings, and enters the chamber.

Then this oil droplet and/or particle can mix   with the unmixed fuel folding  around the air-fuel mixture. And then this newly formed combo will get  exposed to the very high compression ratio,   of the direct injection only engine. And BOOM! The combination gets self-ignited before the spark plug fires, leading to pre-ignition. The results are often catastrophic. And if pre-ignition keeps  occurring and is left untreated,   the engine will likely receive catastrophic  damage, and will need a full rebuild. Of course high mileage engines are more prone to this,   because they will have more deposit  on the back of the intake valves.

And also they will have more wear and tear  on the cylinders and the piston rings,  making it easier for an oil droplet  to make it into the chamber. So here we have an overview of  both port and direct injection. And as we can conclude; Neither setup is really ideal. Direct injection can improve performance,  reduce fuel consumption, and improve emissions. But at the cost of increased  maintenance and some potential problems. So faced with the drawbacks of both setups,  and the need keep meeting  efficiency and emission standards,  car manufacturers have decided to combine  direct import injection into a single setup.

Thus, creating dual injection. Interestingly enough, combining  the two types of injection,  stacks up the benefits but  gets rid of the drawback. The only expense is an increased  number of moving parts. And increased production cost. Because now, instead of only one injector,   each cylinder has to have two injectors,  both a direct injector and a port injector.

So, how does dual injection work? Well, if you watch this video,  you can probably already guess. At low engine RPM, we're going to  rely on the good fuel vaporization  and air-fuel homogenization  properties of port injection. Which means good combustion and  reduced emissions at the low RPMs. It also means that we're spraying fuel  at the backs of the injection valves,   which means no deposits, no  increased maintenance costs. And reduced potential for low-speed pre-ignition. As RPMs and piston speeds  increase, injection steps in.

The high piston speeds means good air-fuel mixing. And the super-accurate nature of direct injection means,   that we can increase the  compression ratio of the engine. Leading to improve performance and efficiency. While at the same time reducing emissions  and fuel consumption at higher engine speeds. Want to rev high and keep  making power at high RPMs? No problem.

When direct injection runs  out of time to do its thing,  the ECU can simply instruct the  port injectors to rejoin the game   at maximum engine loads near the RPM limit. They're going to supply the extra fuel the  direct injection doesn't have the time to supply. And Voila! All the fuel you need at any RPM. And also, all the benefits  and none of the drawbacks. The reason why more and more manufacturers  are packing dual injection into their engines. And there you have it.

Something that I hope is a comprehensive   overview of the three different kinds  of gasoline injection technologies. I hope you enjoyed watching this video. And I hope you learned something in the process,   or maybe answer to a question you  might have had about this topic.

As always, thanks a lot for watching. I'll be seeing you soon, with  more fun and useful stuff. On the D4A channel.

2022-01-18 06:57

Show Video

Other news