iPad Air 3 Battery Replacement 2019

iPad Air 3 Battery Replacement 2019

Show Video

Hi everyone, welcome back to geardo. Today,   we will show you how to replace the  battery in the iPad Air 3 Tablet. Before Starting, we need the right  tools to proceed with the repair,   which are listed in the description. Proper heating is the most crucial  part of iPad repair. For this,  

use a heating pad designed  for tablets and mobile phones. Always heat the front side of the iPad. Select  the tablet heating option and leave it until the   heating process is complete. Alternatively,  a heat gun or a similar tool can be used. Once heating is complete, place a suction  cup on the side of the screen to lift it   slightly. Carefully insert a few  plastic card pry tools into the   gap and slowly slide them around the  edges to cut through the adhesive.

This process takes time, so proceed  with caution to avoid damage.   Be gentle while pulling, as there are delicate  flex cables attached to the logic board. Once the screen is fully separated, carefully tilt  it upward to a 90-degree angle from the top. Do  

not lift the screen from the bottom, as the home  button and display cables are still attached.  Handle the screen gently to  avoid damaging the flex cables. While holding the screen at a 90-degree angle,   carefully remove the two  screws securing the shield.   Then, disconnect the four connector  plugs to detach the front screen   assembly from the body. Handle the  connectors gently to avoid damage. Now you can free the screen from the body. Next, disconnect two antenna heads from the board.

Next, undo four screws on the charging port. Next, undo two screws on the logic board area.  ( middle of the board and battery connector Next, gently remove the logic  board bracket using a pry tool. Next, take out the silver  bracket by undoing five screws. Next, disconnect the headphone jack, microphone  and front camera plugs from the board.

And then, disconnect the back camera,  Volume & power connectors from the board. Next, take out the logic board from the  body. This process should proceed with   gentle care due to the glue under the board.  You can use a heat gun for this process. The   Logic Board is L-shaped, and it is best  to start with the small horizontal strip.  Gently apply heat using a heat gun while  loosening the board using a pry tool.

Also, make sure to disconnect the  smart connector plug from the board. Next, gently pull out the board  while moving the speaker cable. Next, take out the not-working  battery from the body. First, the adhesive securing the non-working  battery must be loosened. To do this,   apply additional heat to the rear side of  the iPad, where the battery is located. Use   a heating pad with the appropriate temperature  or, use a heat gun or hair dryer on low heat.

Do not apply heat consistently  while using the heat gun,   and do not use heat if the battery is swollen. Next, gently cut through the adhesive beneath the  battery using a plastic pry tool. Take your time,   as the adhesive is strong. Avoid using metal tools  to prevent puncturing or damaging the battery.  Slowly cut through the adhesive using a  plastic pry tool, applying gentle pressure   to avoid damage and applying steady pressure  to lift the battery safely from the body. Keep in mind that there is no  connector plug—the battery pins   make direct contact with the logic board pins. This process will take time and needs patience.

Now   gently, pull out the battery from the body. Next, place the new battery with adhesive. Next, place and secure the Logic board in the  body. Gently insert the charger port side to the   opening and securely place it in the body. Be gentle with top flex   cables while laying the board. Make sure  to pull it out before securing the board. Next, ensure the speaker plugs are  connected and tapes are secured.

Next, secure the back camera plug,   and Volume Button connector &  power button plugs to the board. Next, secure the Front camera, microphone  and headphone flex connectors to the board. Next, Secure two antenna connectors.

Next, secure four screws on the charging port. Next, secure the battery connector screw. Next, secure the logic board  shield. and then secure the screw.

Next, secure the silver  bracket by adding five screws. Next, place the LCD assembly into the body  by securing the four connector plugs. Hold   the LCD assembly at a 90-degree angle  to prevent stressing the flex cables,   then secure the four plugs to the board.

This process can be slightly challenging due  to the length of the connector cables. Try   laying the housing body at a 120-degree  angle from the bottom for better reach. Make sure all connections are secured, and  then add the shield by inserting two screws. Next, Before clamping, it is good to verify  the screen functionality and then secure   the screen to the body by adding adhesive.  You can use b7000 or double-sided adhesive.

Start by securing the bottom section first,   then move to the top. Simultaneously click the  sides and bottom into place. Apply pressure to   the frame sides and ensure the home button  sits correctly and clicks precisely." Next, use screen bonding clips to  tighten the screen to the frame. If not,   you can use rubber bands and  leave them for some time.

Hope you have enjoyed the screen Repair guide. Let us know if you have any questions; please  like, share, and comment on our videos. Do not forget to hit the subscribe button.

2025-02-26 17:48

Show Video

Other news

Tech News 10: Mind-Control Is Real, Krutrim, Cursor, Meta Mocha, Runway Gen 4, Dark Energy 2025-04-11 14:38
10 Key Breakthrough Technologies of 2025 2025-04-05 16:31
Strange Tech from the Quantum Realm! 2025-04-04 17:45